Internet of things Starter Kit for NodeMCU

Rs 4,450.00
Ex Tax: Rs 4,450.00
Product Code: NodeMCU
Availability: In Stock


If you want to learn how to build something cool and Internet-connected, all you need is this starter kit which will get you going with lots of parts that go very well with our service and are the most common sensors and actuators you may want. Sense light, motion, humidity, temperature, and more, then send it through MQTT broker and light up remote LEDs, make noise, and move a motor when a trigger is detected.

This pack is designed for people who want to use the new low-cost Arduino compatible NodeMCU (an ESP8266 WiFi microcontroller). An Arduino or other microcontroller is not required.

We pick up 13 kinds of modules to go with our NodeMCU Board. All of them could be DIY into a small IoT applications, as you have learned our 15 detail lessons about these modules.The guide book contains step by step instructions of how to achieve the goal function. Full example code is provided and explained and even includes some useful software tools also be provided.

 What you'll learn

  • How to program an Nodemcu microcontroller

  • Ways to interface Nodemcu with analog and digital sensors (detecting things like light, noise, or pressure)

  • How to use a software library to control motors, lights, sounds, and more

  • Internet of things

  • Build your own innovative project with Nodemcu


This tutorial is about how to use the Thingerbits NodeMCU Kit with the Arduino IDE, it is designed to facilitate beginners and developers to quickly learn Arduino and IoT technology. It help users to turn the idea into a practical application and make the Internet of Things a reality.

  • Lesson 1 - Install the ESP8266 Board Package and the Serial Port Driver

  • Lesson 2 - Hello World!

  • Lesson 3 - Blink an LED

  • Lesson 4 - Button Control LED

  • Lesson 5 - MQTT & Pubsubclient

  • Lesson 6 - MQTT Basic Example

  • Lesson 7 - Switch Button & MQTT

  • Lesson 8 - DHT11 & MQTT

  • Lesson 9 - Light Sensor & MQTT

  • Lesson 10 - Buzzer & MQTT

  • Lesson 11 - Potentiometer & MQTT

  • Lesson 12 - Tilt Sensor & MQTT

  • Lesson 13 - infrared Remote Control & MQTT

  • Lesson 14 - 4-Digit 7 Segment LED Display & MQTT

  • Lesson 15 - I2C 1602 LCD & MQTT

  • Lesson 16 - Step Motor & MQTT

  • Lesson 17 - Servo & MQTT


  • ESP8266 WIFI NODEMCU Board x1

  • Micro USB cable x1

  • I2C LCD Display x1

  • Servo Motor x1

  • DHT11 Temp & Humi Sensor Module x1

  • Tilt Sensor(SW-520D) x1

  • 4 LED module x1

  • Stepper Motor + Bridge x1

  • Potentiometer (10Ω adjustable resistor) x3

  • Buzzer x1

  • Photoresistor (Light Sensor) x1

  • Infrared Receiver x1

  • Infrared Remote Controller x1

  • White LED x6

  • Red LED x6

  • Yellow LED x6

  • Green LED x6

  • Push Buttons x6

  • Breadboard x1

  • 4AA Battery Holder x1

  • 220Ω Resistors x20

  • 10KΩ Resistors x20

  • 1KΩ Resistors x20

  • 1M Resistors x5

  • 40 Pin Jumper Wires (15cm, M to M) x1

  • 20 Pin Jumper Wires (15cm, F to F) x1

  • Resistor Color Code Card x1

Write a review

Note: HTML is not translated!
    Bad           Good